Bike Tires of all kinds from Bicycletires.com

Good tubular tires (this is crucial because crummy tires can be very difficult to install properly, often wear prematurely and develop glitches such as the basetape separating from the tire)

glue (clear or white glues are easier to use and less messy than red ones.

plastic baggies

used sew-up rims or wheels

cone wrench

medium emery cloth

acetone

spoke or piece of wire

flux brushes (available at hardware stores for next to nothing)

1. Stretching tires. Installing new tires is easiest if you stretch them first. A handy way to do this is to keep some used rims or wheels around to be used as stretchers. By storing new tires on rims, the treads will be ready when it’s time to install new rubber on your good wheels and you won’t have to wait for the new ones to stretch on your main rims. New tubs can be tough to put on rims. Some folks recommend hanging the tubular over one shoulder and putting a knee through the bottom loop of the tire and then straightening your back and leg to stretch the tire. I prefer to grip the tire with my hands about a foot apart and pull to stretch that section. Then I repeat this around the entire sew-up. Either approach will make it easier to slip a new tire on a rim. If you have trouble getting the new tire on the rim, use the technique described in step 7.

2. Removing tires. Usually, tires can be removed by hand. If not, you may need to resort to tire levers, wiggling them beneath the basetape and prying to free the tire. Either way, be careful not to separate the basetape from the tire, which complicates removal and means extra work if you plan to use the removed tire as a spare. (The best glue for adhering loose basetape is liquid latex—but it’s getting difficult to find.)

3. Cleaning old rims. It’s almost never necessary to remove old glue. All that’s needed is a smooth, even surface for the new tire. A good way to shape the old glue and knock off any dried blobs is to mount the wheel in the frame (or a truing stand if you have one) and spin the wheel while holding the business end of a cone wrench on the rim. The wrench will act as a shaper and carve and clean the glue bed.

4. Cleaning new rims. The problem with just-built wheels is that there’s often grease or oil still oozing from the rim’s nipple sockets and this can compromise the glue’s integrity. Avoid problems by donning gloves and thoroughly cleaning the rim surface with acetone, which cuts lubricants fast and evaporates immediately. (Work outside to minimize the fumes’ effect.) When the rim has been chemically cleaned, give it a light scouring by sanding with emery cloth, which will increase the rim’s purchase on the tire. Finish by cleaning it again with acetone.

5. Gluing the rim. Place the wheel(s) in the bicycle frame or a truing stand. Open the glue tube by reversing the cap and pushing it back onto the tube to pierce the seal. Because glue can separate during storage, slide a spoke into the glue tube and stir well. When it’s mixed, carefully go around the rim and apply a dab of glue between each pair of spoke holes. Then place your finger in a baggie and rest your finger on the rim while slowly turning the wheel. With a little practice you’ll get the feel for smearing the glue just right to leave an even coat that reaches from sidewall to sidewall. Wait about 30 minutes for the first coat to set up and apply a second coat of glue. Push the point of an old pencil in the valve hole to clean out any glue that’s there.

6. Gluing the tire. Lay the tire flat or suspend it so that part of the inside of the tire faces up with the tire resting on the bench. Carefully run a bead of glue about the diameter of a phone cord down the center of the basetape all the way around the inside of the tire. Use a flux brush to spread the glue to cover the entire base tape. As you did with the rim, wait 30 minutes and apply a second coat.

7. Mounting the tire. Don’t attempt to install the tire until the glue is tacky to the touch. Consider wearing cloth gloves to protect your hands and improve your grip. Work on a hard surface, wood or tile, something that won’t stick to the glue. Place the wheel upright with the valve hole facing up, the wheel resting against your shins. Hold the tire so that your hands straddle the valve stem, each hand about 10 inches away. Don’t touch the glue and keep the glued portion of the tire from touching the rim sidewalls. Lay the tire over the top and front of the wheel and start installation by placing the valve stem into the valve hole. Now, simultaneously, push downward against the floor while gradually lifting and placing the tire on the rim as you work your hands away from each other and toward the floor. Put considerable downward pressure on the tire/wheel. The glue will act as a lubricant helping the tire stretch slightly as you push downward. As your hands nearly reach the floor, push them towards each other with as much muscle as you can muster. Then lift the wheel and pop on the last section of the tire. If you’ve pushed down hard enough and followed this procedure correctly, there should be sufficient clearance and the tire will be very easy to pop on the rim. Best, there’ll be no glue on the tire or rim sidewalls.

8. Seating (aligning) the tire. Once it’s installed, inflate the tire to about 80 psi. As I said at the outset, good tires seat without a lot of wrestling. There are two things you’re looking for: tread that runs straight when you spin the wheel and sight the tread, and even exposure of basetape on both sides of the rim. For the latter, sight the bottom of the spinning tire and check that the same amount of basetape shows on both sides. Correct imperfections by twisting the tire at the areas that need alignment. Another method is to roll the tire on the ground while pressing down on the wheel with your body weight, which sometimes centers the tire with no further effort. Let the tire sit for 24 hours before riding so the glue can dry. One final tip: Many sew-ups use removable valve cores (look for wrench flats near the tip of the valve), a nice feature because they can be replaced if they get damaged. If yours has the flats, it’s a good idea to check the tightness of the valve by turning clockwise with a small adjustable wrench. You may just prevent a slow leak.

How to Mount a Tubular tire

Our Most Popular Articles: